X-Factory

Pentagramm Set Pranger
!
!
Set Basis with Heavy Duty Pillories 1100140
More »
Click on image to view slide show
!

Find more possible applications in our Photogallery

Module Platform Base Plate

Pentagram shaped base plate with star shaped molding
Dimensions:  131 x 124 x 13 cm 51 5/8 x 48 7/8 x 5 1/8 inchesDue to the 5 lockable wheels the whole system is easy to move.  On the top 5 sturdy eyehooks. The different support pipes are easily mounted in either the center or the perimeter positions.  On these vertical pipes the module system accessories are quick to install and remove.  The base plate itself already offers a large variety of possibilities for restraints.

Naturally the pads are protected against sliding and you have the choice between genuine leather or easy – care pleather material.  The pads can also be ordered seperatly at a later time.

 

Beam

Material: solid beech wood, black finish
Dimensions:  130 x 12 x 16 cm
51 2/8 x 4 ¾ x 6 3/8 inches

The beam is easily installed on its support pipes.  The 4 pulleys are located on the inside for precise guidance of the cable.  The cable can be either used on the outsides or as a central rope.

On the front and back of the „Beam“3 fixed eyehooks can be installed.

Maximum capacity:  (120kg), 265 pounds

Support Pipes High

Material:  High grade steel, polished surface
Most of the module system accessories are mounted onto these support pipes.  They can be used in combination with any base plate and installed in the center or perimeter position.

Standard length: (240cm), 94 ½ inches
Important comment: all pipes used have to leave a (14cm), 5 ½ inches clearance from the ceiling, otherwise the module system can not be installed.

Choice of pipe length: (230cm), 90 ½ - (260cm), 102 ¼ inches ((3cm), 1 ¼ inches apart in length, see menu)


Cable Winch

Material: solid beech wood, black finish, with a sturdy metal construction

The „Cable Winch“is easily mounted onto one of the support pipes.  It is equipped with 2 steel cables, one of which can be removed with a cotter pin (no additional tools are needed).  The remaining cable can now be guided through the center pulley of the „Beam“.
The „Cable Winch“with one cable can also be utilized in combination with the module system accessory „Top“.

Maximum capacity: (120Kg), 265 pounds

Heavy Duty Pillory

Material: solid beech wood, black finish
Dimensions: all models   
100 x 26 x 4 cm (L/W/H)
39 3/8 x 10 ¼ x 1 ½ inches (L/W/H)

Finally a versatile pillory for the most delicate women hands and burly ones.  Our ingenious system of restraint finally makes it possible to offer the right opening for any size.  The end caps are rigidly fixed onto the support pipes which can be attached in the vertical or horizontal position.  Now you guide the planks of the pillory into the housing of the end cap and lock it securely with bolts.  Don’t worry, for the vertical use there is pins to hold those bolts in place.  Should you not use the „Pillory“, removing the bolts and pulling the boards out of its end cap housing makes it easy to disassemble.

Pillory with holes for hand and feet on its side and an extra opening in the center. What makes this pillory special is the fact that it not only offers holes for the feet on the side but also in the center for both feet together to insure a rigid position of chastity.  In between these holes you also find ones for the hands to restrain both hands and feet at the same time.

1 Pillory for hands and head

The hole for the hands is oval shaped and can be increased in steps of a (5mm),1/8 of an inch from (4cm), 1 ½ - (6cm),2 3/8 inches in diameter (on the small side of the oval).  The hole for the head is round and measures (14cm),5 ½ inches, expandable up to (16cm),6 3/8 inches in diameter.

 

1 Pillory for hands and feet

Foot hole diameter: (9,3cm),3 5/8 inches, expandable to (11,3cm),4 ½ inches (in steps of an (5mm),1/8 of an inch)
Hand hole: oval, on the small side (4cm),1 ½ inches in diameter, expandable to (6cm),2 3/8 inches (in steps of (5mm),1/8 of an inch)

 


Package

1 Modul Platform Base Plate ( Pads optional)

2 Pipes High

1 Beam

1 Cable Wrench

1 Pillory ( Head and Hands )

1 Pillory ( Hands and Feet)

For easier installment of the pillory heads we recommend :

Position Aid 0100890
More »
Click on image to view slide show
!

Material: polished aluminium surface
Dimensions:  190cm 75 ¾ inches

The Position Aid is the perfect tool to be able to install your module system accessory
at the same height every time, no measuring needed.

After mounting one side of your module system accessories you place the positioning plaque
under the part and secure its plaque with a specialty screw.  No additional tools are needed. 
You now have the exact distance to mount further module system parts and fasten it at the same height. 
One positioning plaque per Position Aid is standard. 
If you don’t want to have to readjust every time we suggest multiple positioning plaques. 

Choose: Number of Plaques 1-4

!